Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 252-552-9
CAS number: 35415-27-1
4.1. Description of first aid measures
Keep at rest. Aerate with fresh air. When symptoms persist or in all cases of doubt seek medical advice.
Wash off immediately with soap and plenty of water. When symptoms persist or in all cases of doubt seek medical advice.
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Remove contact lenses. Immediate medical attention is required.
Call a physician immediately. Do not induce vomiting without medical advice.
4.2. Most important symptoms and effects, both acute and delayed
4.3. Indication of any immediate medical attention and special treatment needed
Remove contaminated, soaked clothing immediately and dispose of safely. First aider needs to protect himself.
5.1. Extinguishing media
Suitable extinguishing media
foam, dry chemical, carbon dioxide (CO2), water spray
Unsuitable Extinguishing Media
Do not use a solid water stream as it may scatter and spread fire.
5.2. Special hazards arising from the substance or mixture
Under conditions giving incomplete combustion, hazardous gases produced may consist of:
carbon monoxide (CO)
carbon dioxide (CO2)
Combustion gases of organic materials must in principle be graded as inhalation poisons
Vapours are heavier than air and may spread along floors
5.3. Advice for firefighters
Special protective equipment for firefighters
Fire fighter protection should include a self-contained breathing apparatus (NIOSH-approved or EN 133) and full fire-fighting turn out gear.
Precautions for firefighting
Cool containers / tanks with water spray. Dike and collect water used to fight fire. Keep people away from and upwind of fire.
6.1. Personal precautions, protective equipment and emergency procedures
For non-emergency personnel: For personal protective equipment see section 8. Avoid contact with skin and eyes. Avoid breathing vapors or mists. Keep people away from and upwind of spill/leak. Ensure adequate ventilation, especially in confined areas. Keep away from heat and sources of ignition.
For emergency responders: Personal protection see section 8.
6.2. Environmental precautions
Prevent further leakage or spillage. Do not discharge product into the aquatic environment without pretreatment (biological treatment plant).
6.3. Methods and material for containment and cleaning up
Methods for containment
Stop the flow of material, if possible without risk. Dike spilled material, where this is possible.
Methods for cleaning up
Soak up with inert absorbent material. Keep in suitable, closed containers for disposal. If liquid has been spilt in large quantities clean up promptly by scoop or vacuum. Dispose of in accordance with local regulations. Take necessary action to avoid static electricity discharge (which might cause ignition of organic vapours).
6.4. Reference to other sections
For personal protective equipment see section 8.
7.1. Precautions for safe handling
Advice on safe handling
Avoid contact with skin, eyes and clothing. Wash hands before breaks and immediately after handling the product. Provide sufficient air exchange and/or exhaust in work rooms.
When using, do not eat, drink or smoke. Take off all contaminated clothing immediately. Wash hands before breaks and immediately after handling the product.
Advice on the protection of the environment
See Section 8: Environmental exposure controls.
strong oxidizing agents
7.2. Conditions for safe storage, including any incompatibilities
Advice on protection against fire and explosion
Keep away from sources of ignition - No smoking. Take necessary action to avoid static electricity discharge (which might cause ignition of organic vapours). In case of fire, emergency cooling with water spray should be available. Ground and bond containers when transferring material.
Technical measures/Storage conditions
Keep containers tightly closed in a cool, well-ventilated place. Handle and open container with care.
7.3. Specific end use(s)
Lubricants and lubricant additives
Industrial processing of articles
8.2. Exposure controls
Special adaptations (REACH)
Appropriate Engineering controls
General or dilution ventilation is frequently insufficient as the sole means of controlling employee exposure. Local ventilation is usually preferred. Explosion-proof equipment (for example fans, switches, and grounded ducts) should be used in mechanical ventilation systems.
Personal protective equipment
General industrial hygiene practice
Avoid contact with skin, eyes and clothing. Do not breathe vapours or spray mist. Ensure that eyewash stations and safety showers are close to the workstation location.
Tightly fitting safety goggles. In addition to goggles, wear a face shield if there is a reasonable chance for splash to the face.
Equipment should conform to EN 166
Wear protective gloves. Recommendations are listed below. Other protective material may be used, depending on the situation, if adequate degradation and permeation data is available. If other chemicals are used in conjunction with this chemical, material selection should be based on protection for all chemicals present.
Suitable material nitrile rubber
Reference substance Di-(2-ethylhexyl)-phthalate
Evaluation according to EN 374: level 6
Glove thickness approx 0,55 mm
Break through time > 480 min
Suitable material polyvinylchloride / nitrile rubber
Glove thickness approx 0,9 mm
Skin and body protection
Impervious clothing. Wear face-shield and protective suit for abnormal processing problems.
Respirator with A filter. Full mask with above mentioned filter according to producers using requirements or self-contained breathing apparatus. Equipment should conform to EN 136 or EN 140 and EN 143.
Environmental exposure controls
If possible use in closed systems. If leakage can not be prevented, the substance needs to be suck off at the emersion point, if possible without danger. Observe the exposure limits, clean exhaust air if needed. If recycling is not practicable, dispose of in compliance with local regulations. Inform the responsible authorities in case of leakage into the atmosphere, or of entry into waterways, soil or drains.
Further details on substance data can be found in the registration dossier under the following link:
The reactivity of the product corresponds to the typical reactivity shown by the substance group as described in any text book on organic chemistry.
10.2. Chemical stability
Stable under recommended storage conditions.
10.3. Possibility of hazardous reactions
Hazardous polymerisation does not occur.
10.4. Conditions to avoid
Avoid contact with heat, sparks, open flame and static discharge. Avoid any source of ignition.
10.5. Incompatible materials
strong oxidizing agents, strong acids.
10.6. Hazardous decomposition products
No decomposition if stored and applied as directed
13.1. Waste treatment methods
Disposal required in compliance with all waste management related state and local regulations. The choice of the appropriate method of disposal depends on the product composition by the time of disposal as well as the local statutes and possibilities for disposal.
Uncleaned empty packaging
Contaminated packaging should be emptied as far as possible and after appropriate cleansing may be taken for reuse.
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
Questo sito web si avvale di cookie affinché possiate usufruire della migliore esperienza sui nostri siti web.
Welcome to the ECHA website. This site is not fully supported in Internet Explorer 7 (and earlier versions). Please upgrade your Internet Explorer to a newer version.
Do not show this message again