Reaction mass of ethanol and propan-2-ol

Guidance on Safe Use

First-aid measures

Inhalation: Move exposed person to fresh air. If it is suspected that fumes are still present,

the rescuer should wear an appropriate mask or self-contained breathing

apparatus. Keep person warm and at rest. If not breathing, if breathing is

irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by

trained personnel. It may be dangerous to the person providing aid to give mouthto-

mouth resuscitation. Get medical attention. If unconscious, place in recovery

position and get medical attention immediately. Maintain an open airway. Loosen

tight clothing such as a collar, tie, belt or waistband.

Ingestion: Wash out mouth with water. Remove dentures if any. Move exposed person to

fresh air. Keep person warm and at rest. If material has been swallowed and the

exposed person is conscious, give small quantities of water to drink. Stop if the

exposed person feels sick as vomiting may be dangerous. Do not induce vomiting

unless directed to do so by medical personnel. If vomiting occurs, the head

should be kept low so that vomit does not enter the lungs. Get medical attention if

adverse health effects persist or are severe. Never give anything by mouth to an

unconscious person. If unconscious, place in recovery position and get medical

attention immediately. Maintain an open airway. Loosen tight clothing such as a

collar, tie, belt or waistband.

Skin contact: Flush contaminated skin with plenty of water. Remove contaminated clothing and

shoes. Get medical attention if symptoms occur. Wash clothing before reuse.

Clean shoes thoroughly before reuse.

Eye contact: Immediately flush eyes with plenty of water, occasionally lifting the upper and

lower eyelids. Check for and remove any contact lenses. Continue to rinse for at

least 10 minutes. Get medical attention.

Protection of first-aiders: No action shall be taken involving any personal risk or without suitable training. It

may be dangerous to the person providing aid to give mouth-to-mouth

resuscitation.

Notes to physician: No specific treatment. Treat symptomatically. Contact poison treatment specialist

immediately if large quantities have been ingested or inhaled.

Fire-fighting measures

Extinguishing media

Suitable: Use dry chemical, CO2, water spray (fog) or foam.

Not suitable: Do not use water jet.

Special exposure hazards: Highly flammable liquid. In a fire or if heated, a pressure increase will occur and

the container may burst, with the risk of a subsequent explosion. Runoff to sewer

may create fire or explosion hazard.

Promptly isolate the scene by removing all persons from the vicinity of the incident

if there is a fire. No action shall be taken involving any personal risk or without

suitable training. Move containers from fire area if this can be done without risk.

Use water spray to keep fire-exposed containers cool.

Hazardous combustion products: Decomposition products may include the following materials:

carbon oxides

Special protective equipment for fire-fighters: Fire-fighters should wear appropriate protective equipment and self-contained

breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Accidental release measures

Personal precautions: No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from

entering. Do not touch or walk through spilled material. Shut off all ignition

sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or

mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is

inadequate. Put on appropriate personal protective equipment (see section exposure controls/personal protection).

Environmental precautions: Avoid dispersal of spilled material and runoff and contact with soil, waterways,

drains and sewers. Inform the relevant authorities if the product has caused

environmental pollution (sewers, waterways, soil or air).

Large spill: Notify police and fire brigade as soon as possible.

Stop leak if without risk. Move containers from spill area. Approach release from

upwind. Prevent entry into sewers, water courses, basements or confined areas.

Wash spillages into an effluent treatment plant or proceed as follows. Contain

and collect spillage with non-combustible, absorbent material e.g. sand, earth,

vermiculite or diatomaceous earth and place in container for disposal according to

local regulations (see section disposal considerations). Use spark-proof tools and explosion-proof

equipment. Dispose of via a licensed waste disposal contractor. Contaminated

absorbent material may pose the same hazard as the spilled product. Note: see

emergency contact information and section disposal considerations for waste disposal.

Small spill: Stop leak if without risk. Move containers from spill area. Dilute with water and

mop up if water-soluble or absorb with an inert dry material and place in an

appropriate waste disposal container. Use spark-proof tools and explosion-proof

equipment. Dispose of via a licensed waste disposal contractor.

Handling and storage

Handling: Put on appropriate personal protective equipment (see section exposure controls/personal protection). Eating, drinking

and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Do not breathe vapor or mist. Do not ingest. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces

unless adequately ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks, open flame or any other ignition source.

Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use non-sparking tools. Take precautionary measures against

electrostatic discharges. To avoid fire or explosion, dissipate static electricity during transfer by grounding and bonding containers and equipment before transferring material. Empty containers retain product residue and can be hazardous. Do not reuse container.

Storage: Store in accordance with local regulations. Store in a segregated and approved

area. Store in original container protected from direct sunlight in a dry, cool and

well-ventilated area, away from incompatible materials (see section stability and reactivity) and food

and drink. Eliminate all ignition sources. Separate from oxidizing materials. Keep

container tightly closed and sealed until ready for use. Containers that have been

opened must be carefully resealed and kept upright to prevent leakage. Do not

store in unlabeled containers. Use appropriate containment to avoid environmental contamination.

Packaging materials

Recommended: Use original container

Austria - VbF class: A I Very dangerous flammable liquid.

Czech Republic - Storage code: I

Transport information

Shipping

SpecialProvisions

Shipping

Remarks

Marine transport (UN RTDG/IMDG)

Shipping

Remarks

Shipping

Remarks

SpecialProvisions

Exposure controls / personal protection

Europe: Ingredient name; Occupational exposure limits

Ethanol; ACGIH TLV (United States, 1/2006). Notes: 1996 Adoption Refers

to Appendix A -- Carcinogens.

TWA: 1880 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; ACGIH (United States, 1994).

TWA: 983 mg/m³

STEL: 1230 mg/m³

TWA: 400 ppm

STEL: 500 ppm

ACGIH TLV (United States, 1/2006). Notes: Refers to Appendix A

-- Carcinogens. ACGIH 2003 Adoption

STEL: 400 ppm 15 minute(s).

TWA: 200 ppm 8 hour(s).

Sweden; Ingredient name; Occupational exposure limits

Ethanol; AFS (Sweden, 6/2005).

STEL: 1900 mg/m³ 15 minute(s).

STEL: 1000 ppm 15 minute(s).

TWA: 1000 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; AFS (Sweden, 6/2005).

STEL: 600 mg/m³ 15 minute(s).

STEL: 250 ppm 15 minute(s).

TWA: 350 mg/m³ 8 hour(s).

TWA: 150 ppm 8 hour(s).

Denmark; Ingredient name; Occupational exposure limits

Ethanol; Arbejdstilsynet (Denmark, 4/2005).

TWA: 1900 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; Arbejdstilsynet (Denmark, 4/2005).

TWA: 490 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s). Carcinogen

Norway; Ingredient name; Occupational exposure limits

Ethanol; Arbeidstilsynet (Norway, 10/2003).

TWA: 950 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; Arbeidstilsynet (Norway, 10/2003).

TWA: 245 mg/m³ 8 hour(s).

TWA: 100 ppm 8 hour(s).

France; Ingredient name; Occupational exposure limits

Ethanol; INRS (France, 2/2006). Notes: indicative exposure limits

STEL: 9500 mg/m³ 15 minute(s). Form: Risk for sensitisation

STEL: 5000 ppm 15 minute(s). Form: Risk for sensitisation

TWA: 1900 mg/m³ 8 hour(s). Form: Risk for sensitisation

TWA: 1000 ppm 8 hour(s). Form: Risk for sensitisation

Propan-2-ol; INRS (France, 2/2006). Notes: indicative exposure limits

STEL: 980 mg/m³ 15 minute(s). Form: Risk for sensitisation

STEL: 400 ppm 15 minute(s). Form: Risk for sensitisation

Netherlands; Ingredient name; Occupational exposure limits

Ethanol; Nationale MAC-lijst (Netherlands, 1/2006). Notes: Administrative

OEL, 8-h TWA: 1000 mg/m³ 8 hour(s).

OEL, 8-h TWA: 500 ppm 8 hour(s).

Propan-2-ol; Nationale MAC-lijst (Netherlands, 1/2006). Notes: Legal

OEL, 8-h TWA: 650 mg/m³ 8 hour(s).

OEL, 8-h TWA: 250 ppm 8 hour(s).

Germany; Ingredient name; Occupational exposure limits

Ethanol; MAK-Werte Liste (Germany, 7/2005).

PEAK: 1920 mg/m³, 4 times per shift, 15 minute(s).

PEAK: 1000 ppm, 4 times per shift, 15 minute(s).

TWA: 960 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

TRGS900 (Germany, 1/2006).

PEAK: 1920 mg/m³ 15 minute(s).

PEAK: 1000 ppm 15 minute(s).

TWA: 960 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; MAK-Werte Liste (Germany, 7/2005).

PEAK: 1000 mg/m³, 4 times per shift, 15 minute(s).

PEAK: 400 ppm, 4 times per shift, 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

TRGS900 (Germany, 1/2006).

PEAK: 1000 mg/m³ 15 minute(s).

PEAK: 400 ppm 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

Finland; Ingredient name; Occupational exposure limit

Ethanol; Työterveyslaitos (Finland, 4/2005).

STEL: 2500 mg/m³ 15 minute(s).

STEL: 1300 ppm 15 minute(s).

TWA: 1900 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; Työterveyslaitos (Finland, 4/2005).

STEL: 620 mg/m³ 15 minute(s).

STEL: 250 ppm 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

United kingdom; Ingredient name; Occupational exposure limit

Ethanol; EH40-WEL (United Kingdom (UK), 1/2005).

WEL 8 hrs limit: 1920 mg/m³ 8 hour(s).

WEL 8 hrs limit: 1000 ppm 8 hour(s).

Propan-2-ol; EH40-WEL (United Kingdom (UK), 1/2005).

WEL 15 min limit: 1250 mg/m³ 15 minute(s).

WEL 15 min limit: 500 ppm 15 minute(s).

WEL 8 hrs limit: 999 mg/m³ 8 hour(s).

WEL 8 hrs limit: 400 ppm 8 hour(s).

Austria; Ingredient name; Occupational exposure limit

Ethanol; BMWA_MAK (Austria, 4/2004).

PEAK: 3800 mg/m³, 3 times per shift, 60 minute(s).

PEAK: 2000 ppm, 3 times per shift, 60 minute(s).

TWA: 1900 mg/m³, 3 times per shift, 60 minute(s).

TWA: 1000 ppm, 3 times per shift, 60 minute(s).

Propan-2-ol; BMWA_MAK (Austria, 4/2004).

STEL: 2000 mg/m³, 4 times per shift, 15 minute(s).

STEL: 800 ppm, 4 times per shift, 15 minute(s).

TWA: 500 mg/m³, 4 times per shift, 15 minute(s).

TWA: 200 ppm, 4 times per shift, 15 minute(s).

Switzerland; Ingredient name; Occupational exposure limit

Ethanol; SUVA (Switzerland, 2/2005). Notes: not temporary

STEL: 1920 mg/m³ 15 minute(s).

STEL: 1000 ppm 15 minute(s).

TWA: 960 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; SUVA (Switzerland, 2/2005). Notes: not temporary

STEL: 1000 mg/m³ 15 minute(s).

STEL: 400 ppm 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

Belgium; Ingredient name; Occupational exposure limit

Ethanol; Lijst Grenswaarden / Valeurs Limites (Belgium, 12/2002).

TWA: 1907 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; Lijst Grenswaarden / Valeurs Limites (Belgium, 12/2002).

STEL: 1248 mg/m³ 15 minute(s).

STEL: 500 ppm 15 minute(s).

TWA: 997 mg/m³ 8 hour(s).

TWA: 400 ppm 8 hour(s).

Spain; Ingredient name; Occupational exposure limit

Ethanol; INSHT (Spain, 1/2006).

TWA: 1910 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; INSHT (Spain, 1/2006).

STEL: 1250 mg/m³ 15 minute(s).

STEL: 500 ppm 15 minute(s).

TWA: 998 mg/m³ 8 hour(s).

TWA: 400 ppm 8 hour(s).

Turkey

No exposure limit value known

Czech Republic; Ingredient name;Occupational exposure limit

Ethanol; 178/2001 (Czech Republic, 6/2004).

STEL: 3000 mg/m³ 10 minute(s).

STEL: 1596 ppm 10 minute(s).

TWA: 1000 mg/m³ 8 hour(s).

TWA: 532 ppm 8 hour(s).

propan-2-ol; 178/2001 (Czech Republic, 6/2004). Skin

STEL: 1000 mg/m³ 10 minute(s).

STEL: 407 ppm 10 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 203.5 ppm 8 hour(s).

Ireland; Ingredient name; Occupational exposure limit

Ethanol; NAOSH (Ireland, 3/2002).

OELV-8hr: 1900 mg/m³ 8 hour(s).

OELV-8hr: 1000 ppm 8 hour(s).

Propan-2-ol; NAOSH (Ireland, 3/2002). Skin

OELV-15min: 1225 mg/m³ 15 minute(s).

OELV-15min: 500 ppm 15 minute(s).

OELV-8hr: 980 mg/m³ 8 hour(s).

OELV-8hr: 400 ppm 8 hour(s).

Italy

No exposure limit value known.

Estonia; Ingredient name; Occupational exposure limit

Ethanol; Sotsiaalminister (Estonia, 9/2001).

STEL: 1900 mg/m³ 15 minute(s).

STEL: 1000 ppm 15 minute(s).

TWA: 1000 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; Sotsiaalminister (Estonia, 9/2001).

STEL: 600 mg/m³ 15 minute(s).

STEL: 250 ppm 15 minute(s).

TWA: 350 mg/m³ 8 hour(s).

TWA: 150 ppm 8 hour(s).

Lithuania; Ingredient name; Occupational exposure limit

Ethanol; Del Lietuvos Higienos Normos (Lithuania, 12/2001).

STEL: 1900 mg/m³ 15 minute(s).

STEL: 1000 ppm 15 minute(s).

TWA: 1000 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propanol-2-ol; Del Lietuvos Higienos Normos (Lithuania, 12/2001).

STEL: 600 mg/m³ 15 minute(s).

STEL: 250 ppm 15 minute(s).

TWA: 350 mg/m³ 8 hour(s).

TWA: 150 ppm 8 hour(s).

Slovakia; Ingredient name; Occupational exposure limit

Ethanol; Nariadenie Vlády Slovenskej republiky (Slovakia, 1/2002).

TWA: 960 mg/m³ 8 hour(s).

TWA: 500 ppm 8 hour(s).

Propan-2-ol; Nariadenie Vlády Slovenskej republiky (Slovakia, 1/2002).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

Hungary;  Ingredient name; Occupational exposure limit

Ethanol; EüM-SzCsM (Hungary, 11/2002).

PEAK: 7600 mg/m³ 15 minute(s).

TWA: 1900 mg/m³ 8 hour(s).

Propan-2-ol; EüM-SzCsM (Hungary, 11/2002). Skin

PEAK: 2000 mg/m³ 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

Poland; Ingredient name; Occupational exposure limit

Ethanol; Ministra Pracy I Polityki Społecznej (Poland, 10/2005).

TWA: 1900 mg/m³ 8 hour(s).

Propan-2-ol; Ministra Pracy I Polityki Społecznej (Poland, 10/2005).

STEL: 1200 mg/m³ 15 minute(s).

TWA: 900 mg/m³ 8 hour(s).

Slovenia; Ingredient name; Occupational exposure limit

Ethanol; Uradni list Republike Slovenije (Slovenia, 4/2005).

PEAK: 7600 mg/m³, 4 times per shift, 15 minute(s).

PEAK: 4000 ppm, 4 times per shift, 15 minute(s).

TWA: 1900 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; Uradni list Republike Slovenije (Slovenia, 4/2005).

PEAK: 2000 mg/m³, 4 times per shift, 15 minute(s).

PEAK: 800 ppm, 4 times per shift, 15 minute(s).

TWA: 500 mg/m³ 8 hour(s).

TWA: 200 ppm 8 hour(s).

Latvia; Ingredient name; Occupational exposure limit

Ethanol; LV Nat. Standardisation and Meterological Centre (Latvia,

11/2004).

TWA: 1000 mg/m³ 8 hour(s).

Propan-2-ol; LV Nat. Standardisation and Meterological Centre (Latvia,

11/2004).

STEL: 600 mg/m³ 15 minute(s).

TWA: 350 mg/m³ 8 hour(s).

Greece; Ingredient name; Occupational exposure limit

Ethanol; PD 90/1999 (Greece, 2/2003).

TWA: 1900 mg/m³ 8 hour(s).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; PD 90/1999 (Greece, 2/2003).

STEL: 1225 mg/m³ 15 minute(s).

STEL: 500 ppm 15 minute(s).

TWA: 980 mg/m³ 8 hour(s).

TWA: 400 ppm 8 hour(s).

Portugal; Ingredient name; Occupational exposure limit

Ethanol; Instituto Português da Qualidade (Portugal, 7/2004).

TWA: 1000 ppm 8 hour(s).

Propan-2-ol; Instituto Português da Qualidade (Portugal, 7/2004).

STEL: 500 ppm 15 minute(s).

TWA: 400 ppm 8 hour(s).

Recommended monitoring procedures:If this product contains ingredients with exposure limits, personal, workplace

atmosphere or biological monitoring may be required to determine the

effectiveness of the ventilation or other control measures and/or the necessity to

use respiratory protective equipment. Reference should be made to European

Standard EN 689 for methods for the assessment of exposure by inhalation to

chemical agents and national guidance documents for methods for the

determination of hazardous substances.

Exposure controls

Occupational exposure controls

Use only with adequate ventilation. Use process enclosures, local exhaust

ventilation or other engineering controls to keep worker exposure to airborne

contaminants below any recommended or statutory limits. The engineering

controls also need to keep gas, vapor or dust concentrations below any lower

explosive limits. Use explosion-proof ventilation equipment.

Hygiene measures; Wash hands, forearms and face thoroughly after handling chemical products,

before eating, smoking and using the lavatory and at the end of the working

period. Appropriate techniques should be used to remove potentially

contaminated clothing. Wash contaminated clothing before reusing. Ensure that

eyewash stations and safety showers are close to the workstation location.

Respiratory protection: Use a properly fitted, air-purifying or air-fed respirator complying with an approved

standard if a risk assessment indicates this is necessary. Respirator selection

must be based on known or anticipated exposure levels, the hazards of the

product and the safe working limits of the selected respirator.

Hand protection: Chemical-resistant, impervious gloves complying with an approved standard

should be worn at all times when handling chemical products if a risk assessment

indicates this is necessary.

Recommended: nitrile rubber

Eye protection: Safety eyewear complying with an approved standard should be used when a risk

assessment indicates this is necessary to avoid exposure to liquid splashes, mists,

gases or dusts.

Skin protection: Personal protective equipment for the body should be selected based on the task

being performed and the risks involved and should be approved by a specialist

before handling this product.

Environmental exposure controls: Emissions from ventilation or work process equipment should be checked to

ensure they comply with the requirements of environmental protection legislation.

In some cases, fume scrubbers, filters or engineering modifications to the process

equipment will be necessary to reduce emissions to acceptable levels.

Protection based on MAL: According to the regulations on work involving coded products, the

following stipulations apply to the use of personal protective equipment:

General: Gloves must be worn for all work that may result in soiling.

Apron/coveralls/protective clothing must be worn when soiling is so great that

regular work clothes do not adequately protect skin against contact with the

product. A face shield must be worn in work involving spattering if a full mask is

not required. In this case, other recommended use of eye protection is not required.

In all spraying operations in which there is return spray, respiratory protection with

air supply and arm protectors/apron/coveralls/protective clothing must be worn as

appropriate or as instructed.

MAL-code: 3-6

Application: When using scraper or knife, brush, roller etc. for pre- and posttreatments

in a spray booth where the operator is outside the spray zone and

when working in similar new* facilities of the combined-cabin, spray-cabin and

spray-booth type where the operator is working inside the spray zone. When

spraying in new* booths and cabins with non-atomizing guns.

- Protective clothing must be worn.

During downtimes, cleaning and repair of closed facilities, spray booths or cabins,

if there is a risk of contact with wet paint or organic solvents. When using scraper

or knife, brush, roller, etc. for pre- and post-treatments in cabins or booths of the

existing* facility type, if the operator is inside the spray zone. When using scraper

or knife, brush, roller, etc. for pre- and post-treatments outside a closed facility,

spray booth or spray cabin.

- Air-supplied half mask, protective clothing and eye protection must be worn.

When spraying in new* booths if the operator is outside the spray zone.

- Air-supplied half mask and eye protection must be worn.

When spraying in existing* spray booths, if the operator is outside the spray zone.

During non-atomizing spraying in existing* facilities of the combined-cabin, spraycabin

and spray-booth type where the operator is working inside the spray zone.

- Air-supplied full mask and protective clothing must be worn.

During all spraying where atomization occurs in cabins or spray booths where the

operator is inside the spray zone and during spraying outside a closed facility,

cabin or booth.

- Air-supplied full mask, protective clothing and hood must be worn.

Drying: Items for drying/drying ovens that are temporarily placed on such things

as rack trolleys, etc. must be equipped with a mechanical exhaust system to

prevent fumes from wet items from passing through workers' inhalation zone.

Polishing: When polishing treated surfaces, a mask with dust filter must be

worn. When machine grinding, eye protection must be worn. Work gloves must

always be worn.

Caution The regulations contain other stipulations in addition to the above.

*See Regulations.

Stability and reactivity

Stability: The product is stable. Under normal conditions of storage and use, hazardous

polymerization will not occur.

Conditions to avoid: Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut,

weld, braze, solder, drill, grind or expose containers to heat or sources of ignition.

Materials to avoid: Highly reactive or incompatible with the following materials: oxidizing materials

Hazardous decomposition products: Under normal conditions of storage and use, hazardous decomposition products

should not be produced.  

Disposal considerations

Methods of disposal: Incinerate unwanted products.

The generation of waste should be avoided or minimized wherever possible.

Avoid dispersal of spilled material and runoff and contact with soil, waterways,

drains and sewers. Disposal of this product, solutions and any by-products should

at all times comply with the requirements of environmental protection and waste

disposal legislation and any regional local authority requirements.

Hazardous waste: The classification of the product may meet the criteria for a hazardous waste.

Denmark – Carcinogenic waste: Waste containers must be labeled: Contains a substance or substances regulated

by Danish working environment legislation on cancer risks.

Norway - Hazardous waste: The classification of the product may meet the criteria for a hazardous waste.