Registration Dossier

Data platform availability banner - registered substances factsheets

Please be aware that this old REACH registration data factsheet is no longer maintained; it remains frozen as of 19th May 2023.

The new ECHA CHEM database has been released by ECHA, and it now contains all REACH registration data. There are more details on the transition of ECHA's published data to ECHA CHEM here.

Diss Factsheets

Administrative data

First-aid measures

· General information: Remove contaminated clothes. Get Medical attention immediately.`
· After inhalation:
Move to fresh air. If difficulty in breathing, give oxygen. If not breathing, give artificial respiration. Get emergency medical help immediately.
· After skin contact:
Remove affected clothing and launder before reuse. Wash skin area with plenty of soap and water. If any itching, redness, swelling or pain of the skin starts, see a doctor immediately.
· After eye contact:
Immediately rinse with plenty of clean flowing water for 15 to 20 minutes. Call a doctor and get medical attention.
· After swallowing: Rinse mouth and get medical attention immediately.
· Information for doctor: Treat symptomatically and supportively.
· The following symptoms may occur: May cause skin and eye irritation.

Fire-fighting measures

· Suitable extinguishing agents:
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
· Protective equipment: No special measures required.

Accidental release measures

· Person-related safety precautions:
For non-emergency personnel
Wear a NIOSH approved dust respirator with all protective clothing and equipment. Contain and clean up spill immediately.
For emergency responders: Do not touch the spilled material.
· Measures for environmental protection: Do not allow the material to enter into drainage system.
· Measures for cleaning/collecting:
Cleaning up:
Sweep powders carefully, using an absorbent (sweeping compound). To keep down the dust in the area, scoop material and absorbent into disposal drums and seal it.

Handling and storage

· Handling:
· Information for safe handling:
Handle the product away from moisture. Avoid handling the product in excessive heat. Avoid dust formation.
Take precautionary measures against static discharges.
· Information about fire - and explosion protection: No special measures required.

· Storage:
· Requirements to be met by storerooms and receptacles: No special requirements.
· Information about storage in one common storage facility:
Store in original or similar waterproof containers. Reseal containers after each use.
· Further information about storage conditions:
How to control the effects of:
(i) Weather conditions: Store in cool and dry place away from moisture.
(ii) Ambient pressure: Not available.
(iii) Temperature: Store in cool place.
(iv) Sunlight: Store away from sunlight.
(v) Humidity: Always store under low relative humidity.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

· Additional information about design of technical facilities: No further data; see item 7.

· Ingredients with limit values that require monitoring at the workplace: Not required.
· Additional information: The lists valid during the making were used as basis.

· Personal protective equipment:
· General protective and hygienic measures:
The usual precautionary measures are to be adhered to when handling chemicals.
· Respiratory protection: Not required.
· Protection of hands:
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer.
· Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be
· Eye protection: Not required.

Stability and reactivity

· Thermal decomposition / conditions to be avoided: Avoid dust formation. Keep away from excessive heat.
· Materials to be avoided: Keep away from oxidizing agents.
· Dangerous reactions Will not occur if stored under normal conditions.
· Dangerous decomposition products: May produce irritating and toxic fumes.

Disposal considerations

· Product:
· Recommendation Smaller quantities can be disposed of with household waste.
· Waste disposal key:
Waste Codes :
08 01 : Wastes from Manufacture, Formulation, Supply and Use (MFSU) and removal of paint and varnish
08 03: Wastes from MFSU of printing inks.
· European waste catalogue
•Recycle or rework material if at all possible. Incinerate material in an approved facility.
•Treat at an acceptable waste facility. Dispose of in accordance to all Local, State and Federal Laws.

· Uncleaned packaging:
· Recommendation: Disposal must be made according to official regulations.