Registration Dossier
Registration Dossier
Diss Factsheets
Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 219-676-5 | CAS number: 2495-39-8
- Life Cycle description
- Uses advised against
- Endpoint summary
- Appearance / physical state / colour
- Melting point / freezing point
- Boiling point
- Density
- Particle size distribution (Granulometry)
- Vapour pressure
- Partition coefficient
- Water solubility
- Solubility in organic solvents / fat solubility
- Surface tension
- Flash point
- Auto flammability
- Flammability
- Explosiveness
- Oxidising properties
- Oxidation reduction potential
- Stability in organic solvents and identity of relevant degradation products
- Storage stability and reactivity towards container material
- Stability: thermal, sunlight, metals
- pH
- Dissociation constant
- Viscosity
- Additional physico-chemical information
- Additional physico-chemical properties of nanomaterials
- Nanomaterial agglomeration / aggregation
- Nanomaterial crystalline phase
- Nanomaterial crystallite and grain size
- Nanomaterial aspect ratio / shape
- Nanomaterial specific surface area
- Nanomaterial Zeta potential
- Nanomaterial surface chemistry
- Nanomaterial dustiness
- Nanomaterial porosity
- Nanomaterial pour density
- Nanomaterial photocatalytic activity
- Nanomaterial radical formation potential
- Nanomaterial catalytic activity
- Endpoint summary
- Stability
- Biodegradation
- Bioaccumulation
- Transport and distribution
- Environmental data
- Additional information on environmental fate and behaviour
- Ecotoxicological Summary
- Aquatic toxicity
- Endpoint summary
- Short-term toxicity to fish
- Long-term toxicity to fish
- Short-term toxicity to aquatic invertebrates
- Long-term toxicity to aquatic invertebrates
- Toxicity to aquatic algae and cyanobacteria
- Toxicity to aquatic plants other than algae
- Toxicity to microorganisms
- Endocrine disrupter testing in aquatic vertebrates – in vivo
- Toxicity to other aquatic organisms
- Sediment toxicity
- Terrestrial toxicity
- Biological effects monitoring
- Biotransformation and kinetics
- Additional ecotoxological information
- Toxicological Summary
- Toxicokinetics, metabolism and distribution
- Acute Toxicity
- Irritation / corrosion
- Sensitisation
- Repeated dose toxicity
- Genetic toxicity
- Carcinogenicity
- Toxicity to reproduction
- Specific investigations
- Exposure related observations in humans
- Toxic effects on livestock and pets
- Additional toxicological data

Skin irritation / corrosion
Administrative data
- Endpoint:
- skin irritation: in vitro / ex vivo
- Type of information:
- experimental study
- Adequacy of study:
- key study
- Reliability:
- 1 (reliable without restriction)
- Rationale for reliability incl. deficiencies:
- other: GLP guideline study
Data source
Reference
- Reference Type:
- study report
- Title:
- Unnamed
- Year:
- 2 010
- Report date:
- 2010
Materials and methods
Test guideline
- Qualifier:
- according to guideline
- Guideline:
- other: OECD 431: In vitro Skin Corrosion: Human Skin Model Test
- GLP compliance:
- yes (incl. QA statement)
Test material
- Reference substance name:
- Sodium prop-2-enesulphonate
- EC Number:
- 219-676-5
- EC Name:
- Sodium prop-2-enesulphonate
- Cas Number:
- 2495-39-8
- Molecular formula:
- C3H6O3S.Na
- IUPAC Name:
- sodium prop-2-ene-1-sulfonate
- Details on test material:
- - Name of test substance: Golpanol ALS wasserfrei
- Test-substance No.: 09/0505-1
- Batch identification: 04749356P0
- Purity: Golpanols ALS = 71.3%; NaCI = 26.0%
- Homogeneity: The homogeneity of the test substance was provided after shaking the test-substance container.
- Storage stability: The stability under storage conditions over the study period was guaranteed by the sponsor, and the sponsor holds this responsibility.
ADDITIONAL TEST-SUBSTANCE INFORMATION
-pH-value: Ca. 5.5 (undiluted test substance, moistened with water)
Constituent 1
Test animals
- Species:
- other: EpiDermTM (reconstructed three dimensional human epidermis model)
Test system
- Vehicle:
- unchanged (no vehicle)
- Controls:
- other: Negative control (NC): Highly de-ionized water (corrosion test); PBS, sterile (irrritation test); Positive control (PC): 8-n potassium hydroxide solution
- Amount / concentration applied:
- TEST MATERIAL
- Amount(s) applied (volume or weight with unit): 25 μL bulk volume (about 12 mg) - Duration of treatment / exposure:
- corrosion test: 3 minutes and 1 hour
irritation test: 1 hour - Observation period:
- corrosion test: 3 minutes and 1 hour
irritation test: 1 hour incubation followed by a 42-hours post-incubation period - Number of animals:
- corrosion test :Two tissue samlpes per exposure time and test group (test material, negative control and positive control; 12 tissues per test)
irritation test: three EpiDerm™ tissue samples with the test substance, the PC and NC - Details on study design:
- Corrosion test:
For the corrosion test two EpiDerm™ tissue samples were incubated with the test substance for 3 minutes or 1 hour, respectively. The tissues were washed with PBS to remove residual test material 3 minutes or 1 hour after start of the application treatment. Rinsed tissues were kept in 24-well plates (holding plates) at room temperature on assay medium until all tissues per application time were dosed and rinsed. The assay medium was then replaced by MTT solution and tissues were incubated for 3 hours.
After incubation, tissues were washed with PBS and the formazan produced by the tissues was extracted with isopropanol over night at room temperature. The optical density at a wavelength of 570 nm (OD570) of the extracts was determined spectrophotometrically.
Irritation test:
The tissues were kept under the laminar flow hood at room temperature for 25 minutes overall and for 35 minutes in the incubator.
The tissues were washed with sterile PBS to remove residual test material 1 hour after start of application. Rinsed tissues were blotted on sterile absorbent paper and transferred into new 6-well plates, pre-filled with 0.9 mL fresh medium. When all tissues were rinsed, the surface of each tissue was carefully dried with a sterile cotton swab.
Subsequently, the tissues were incubated in the incubator at 37°C for 24 ± 2 hours.
After 24 ± 2 hours the tissues were transferred into new 6-well plates pre-filled with 0.9 mL of fresh medium and placed into the incubator for additional 18 ± 2 hours post-incubation period.
After the post-incubation period, the assay medium was replaced by 0.3 mL MTT solution and the tissues were incubated in the incubator for 3 hours. After incubation, the tissues were washed with PBS to stop the MTT-incubation.
The formazan that was metabolically produced by the tissues was extracted by incubation of the tissues in isopropanol for at least 2 hours at room temperature on a plate shaker. The optical density at a wavelength of 570 nm (OD570) of the extracts was determined spectrophotometrically.
Results and discussion
In vitro
Resultsopen allclose all
- Irritation / corrosion parameter:
- % tissue viability
- Remarks:
- 3 minutes
- Value:
- ca. 114
- Negative controls validity:
- valid
- Positive controls validity:
- valid
- Remarks on result:
- no indication of irritation
- Irritation / corrosion parameter:
- % tissue viability
- Remarks:
- 1 h
- Value:
- 89
- Negative controls validity:
- valid
- Positive controls validity:
- valid
- Remarks on result:
- no indication of irritation
- Irritation / corrosion parameter:
- % tissue viability
- Remarks:
- 1h incubation 48 h recovery
- Value:
- 95
- Negative controls validity:
- valid
- Positive controls validity:
- valid
- Remarks on result:
- no indication of irritation
Any other information on results incl. tables
The EpiDerm skin corrosivity/irritation test showed the following results:
The test substance is not able to reduce MTT directly.
The mean viability of the test-substance treated tissues determined after an exposure period of 3 minutes was 114%, and it was 89% after an exposure period of 1 hour.
The mean viability of the test-substance treated tissues determined after an exposure period of 1 hour with about 42 hours post-incubation was 95%.
Based on the observed results it was concluded, that Golpanol ALS wasserfrei does not show a skin irritation potential in the EpiDerm skin corrosion/irritation test under the test conditions chosen.
Corrosion Test
|
Exposure time 3 min |
|||
Test-Article |
OD570 tissue 1 |
OD570 tissue 2 |
mean OD570 |
Viability (% of NC) |
NC |
1.7627 |
1.7522 |
1.7574 |
100 |
09/0505 -1 |
1.8622 |
2.1477 |
2.0049 |
114 |
PC_C |
0.4438 |
0.3498 |
0.3968 |
23 |
|
Exposure time 1 h |
|||
Test-Article |
OD570 tissue 1 |
OD570 tissue 2 |
mean OD570 |
Viability (% of NC) |
NC |
1.7657 |
1.6962 |
1.7309 |
100 |
09/0505 -1 |
1.5547 |
1.5312 |
1.5429 |
89 |
PC_C |
0.1597 |
0.1867 |
0.1732 |
10 |
Irritation Test
Test-Article |
OD570 tissue 1 |
OD570 tissue 2 |
OD570 tissue 3 |
mean OD570 |
Viability (% of NC) |
NC |
1.6795 |
1.6125 |
1.5725 |
1.6215 |
100 |
09/0505 -1 |
1.4935 |
1.5625 |
1.5745 |
1.5435 |
95 |
PC_C |
0.1165 |
0.1320 |
0.1215 |
0.1233 |
8 |
NC: Negative control
PC_C: Positive control
OD570: Optical density (wavelength 570 nm)
Applicant's summary and conclusion
- Interpretation of results:
- not irritating
- Remarks:
- Migrated information Criteria used for interpretation of results: other: CLP (1272/2008/EC)
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.
Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
