Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

After inhalation: fresh air.
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
After eye contact: rinse out with plenty of water. Remove contact lenses.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.

Fire-fighting measures

Extinguishing media:
Suitable extinguishing media Water, Foam, Carbon dioxide (CO2), Dry powder
Unsuitable extinguishing media For this substance/mixture no limitations of extinguishing agents are given.

Special hazards arising from the substance or mixture:
Combustible material Development of hazardous combustion gases or vapours possible in the event of fire.

Advice for firefighters:
Special protective equipment for firefighters In the event of fire, wear self-contained breathing apparatus.

Accidental release measures

Personal precautions, protective equipment and emergency procedures:
Advice for non-emergency personnel: Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert.
Advice for emergency responders:
Protective equipment see on SDS

Environmental precautions: Do not let product enter drains.

Methods and materials for containment and cleaning up: Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts.

Reference to other sections Indications about waste treatment see section 13 of SDS

Handling and storage

Precautions for safe handling
Advice on safe handling Observe label precautions.
Hygiene measures Change contaminated clothing. Wash hands after working with substance.

Conditions for safe storage, including any incompatibilities
Storage conditions: Tightly closed. Dry.
Recommended storage temperature see product label.

Specific end use(s) Apart from the uses mentioned in section 1.2 no other specific uses are stipulated.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Additional transport information

Additional information
Special provisions / remarks / other:
Not classified as dangerous in the meaning of transport regulations.

Exposure controls / personal protection

Individual protection measures Protective clothing needs to be selected specifically for the workplace, depending on concentrations and quantities of the hazardous substances handled. The chemical resistance of the protective equipment should be enquired at the respective supplier.
Eye/face protection Safety glasses
Hand protection full contact: Glove material: Nitrile rubber Glove thickness: 0,11 mm Break through time: > 480 min splash contact: Glove material: Nitrile rubber Glove thickness: 0,11 mm Break through time: > 480 min
The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374, for example KCL 741 Dermatril® L (full contact), KCL 741 Dermatril® L (splash contact). The breakthrough times stated above were determined by KCL in laboratory tests acc. to EN374 with samples of the recommended glove types. This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Respiratory protection required when dusts are generated. Recommended Filter type: Filter P 1 (acc. to DIN 3181) for solid particles of inert substances The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.


Environmental exposure controls Do not let product enter drains.

Stability and reactivity

Disposal considerations

Waste treatment methods See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.