Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

General advice
- Show this safety data sheet to the doctor in attendance.
- First aider needs to protect himself.
- Place affected clothing in a sealed bag for subsequent decontamination.

In case of inhalation
- Move to fresh air.
- Keep at rest.
- Consult a physician if necessary.

In case of skin contact
- Take off contaminated clothing and shoes immediately.
- Wash off with soap and plenty of water.

In case of eye contact
- Rinse with running water whilst keeping the eyes wide open (at least 15 minutes)

In case of ingestion
- Do NOT induce vomiting.
- Rinse mouth with water.

Fire-fighting measures

Extinguishing media:

Suitable extinguishing media
- Foam
- Multi-purpose powders
- Carbon dioxide (CO2)
- Water spray

Unsuitable extinguishing media
- High volume water jet

Special hazards arising from the substance or mixture:
- Risk of dust explosion.
- Avoid generating dust; fine dust dispersed in air in sufficient concentrations, and in the presence of an ignition source is a potential dust explosion hazard.
- On combustion, toxic gases are released.

Advice for firefighters:

Special protective equipment for firefighters
- In the event of fire, wear self-contained breathing apparatus.
- Personal protective equipment comprising: suitable protective gloves, safety goggles and protective clothing

Specific fire fighting methods:
- Do not use a solid water stream as it may scatter and spread fire.
- Standard procedure for chemical fires.
- Collect contaminated fire extinguishing water separately. This must not be discharged into drains.
- Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures:
- Wear suitable protective equipment.
- Personal protective equipment
- Wear suitable gloves.
- Avoid contact with the skin and the eyes.
- Tightly fitting safety goggles
- Remove all sources of ignition.
- Do not breathe dust.
- Respirator with a particle filter (EN 143)

Environmental precautions:
- Stop the leak. Turn leaking containers leak-side up to prevent the escape of liquid.
- Contain the spilled material by bunding.
- Do not let product enter drains.
- Do not allow uncontrolled discharge of product into the environment.

Methods and materials for containment and cleaning up:

Recovery
- Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and place in container for disposal according to local regulations (see section 13).
- Keep in suitable, closed containers for disposal.
- Keep in properly labelled containers.
- Avoid dispersal of dust in the air (i.e., clearing dust surfaces with compressed air).

Decontamination/cleaning
- Wash non-recoverable remainder with large amounts of water.
- Clean contaminated surface thoroughly.
- Recover the cleaning water for subsequent disposal.

Disposal
- Dispose of in accordance with local regulations.

Additional advice
- Material can create slippery conditions.

Handling and storage

Precautions for safe handling:
- Provide sufficient air exchange and/or exhaust in work rooms.
- Earth the equipment.
- Take measures to prevent the build up of electrostatic charge.
- Handle in accordance with good industrial hygiene and safety practice.
- Avoid dust formation.
- Routine housekeeping should be instituted to ensure that dusts do not accumulate on surfaces.
- Avoid allowing the dust to build up. Clean regularly.
- Avoid contact of the product with insulating materials during operations which may generate electrostatic charges.
- Keep away from flames and hot surfaces.
- Follow the instructions for use issued by the producer.

Hygiene measures:
- The user is responsible for monitoring the working environment in accordance with local laws and regulations.
- Contaminated work clothing should not be allowed out of the workplace.
- Use clean, well-maintained personal protection equipment.
- When using do not eat, drink or smoke.
- Wash hands before breaks and at the end of workday.
- Regular cleaning of equipment, work area and clothing.

Conditions for safe storage, including any incompatibilities:

Technical measures/Storage conditions
- Take all necessary measures to avoid accidental discharge of products into drains and waterways due to the rupture of containers or transfer systems.
- Do not stack the pallets.
- Stable under normal conditions.
- Keep in a cool, well-ventilated place.
- Protect from moisture.
- Keep away from open flames, hot surfaces and sources of ignition.
- Keep away from incompatible materials to be indicated by the manufacturer
- Keep only in the original container.
- Keep away from: Hazardous reactions may occur on contact with certain chemicals. (Refer to the list of incompatible materials section 10: "Stability-Reactivity").

Packaging material
Suitable material
- Plastic materials.

Transport information

Land transport (UN RTDG/ADR/RID)

UN number:
not regulated
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (UN RTDG/ADN(R))

UN number:
not regulated
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

UN number:
not regulated
Shippingopen allclose all
Remarksopen allclose all

Air transport (UN RTDG/ICAO/IATA)

UN number:
not regulated
Shippingopen allclose all
Special provisions / remarks
Remarks:
ADN/ADNR: not regulated
ADR: not regulated
RID: not regulated
IMDG: not regulated
IATA: not regulated
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control measures
Engineering measures
- Extract at emission point.
- Ensure that extracted air cannot be returned to the workplace through the ventilation system.
- Provide adequate ventilation.

Individual protection measures
Respiratory protection
- Use a respirator with an approved filter if a risk assessment indicates this is necessary.
Hand protection
- Where there is a risk of contact with hands, use appropriate gloves
- Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion, and the contact time.
- Gloves must be inspected prior to use.
- Gloves should be discarded and replaced if there is any indication of degradation or chemical breakthrough.

Suitable material
- Latex gloves

Eye protection
- Tightly fitting safety goggles

Skin and body protection
- Full protective suit
- Choose body protection according to the amount and concentration of the dangerous substance at the work place.

Hygiene measures
- The user is responsible for monitoring the working environment in accordance with local laws and regulations.
- Contaminated work clothing should not be allowed out of the workplace.
- Use clean, well-maintained personal protection equipment.
- When using do not eat, drink or smoke.
- Wash hands before breaks and at the end of workday.
- Regular cleaning of equipment, work area and clothing.

Protective measures
- Emergency equipment immediately accessible, with instructions for use.
- Ensure that eyewash stations and safety showers are close to the workstation location.
- Selection of appropriate personal protective equipment should be based on an evaluation of the performance characteristics of the protective equipment relative to the task(s) to be performed, conditions present, duration of use, and the potential hazards and/or risks that may occur during use.
- The protective equipment must be selected in accordance with current CEN standards and in cooperation with the supplier of the protective equipment.
- The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.

Environmental exposure controls
- Dam up.
- Prevent product from entering sewage system.

Stability and reactivity

Reactivity
- no data available

Chemical stability
- Stable under recommended storage conditions.

Possibility of hazardous reactions
polymerisation
- Hazardous polymerisation does not occur.

Conditions to avoid
- Keep away from heat and sources of ignition.
- Keep away from flames and sparks.
- Static electricity
- Avoid dust formation.

Incompatible materials
- Strong oxidizing agents
- Strong acids
- Strong bases

Hazardous decomposition products
Hazardous decomposition products
- On combustion or on thermal decomposition (pyrolysis) releases:
- (Carbon oxides (CO + CO2)).
- Nitrogen oxides (NOx)

Disposal considerations

Waste treatment methods
Product Disposal
Prohibition
- Avoid release to the environment.
- Dispose of as hazardous waste in compliance with local and national regulations.
Advice on cleaning and disposal of packaging
- Empty the packaging completely prior to disposal.
- Dispose of contents/ container to an approved waste disposal plant.
- Dispose of in accordance with local regulations.
Measure for waste avoidance or recovery
- Do not dispose of the product at a rubbish tip.

Categories Display