Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

Description of first aid measures

Eye contact - Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.

Skin contact - Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.

Ingestion - Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not induce vomiting unless directed by medical personnel. Seek medical attention immediately.

Inhalation - Remove to fresh air and keep patient at rest. Seek medical attention immediately.

Most important symptoms and effects, both acute and delayed

Symptoms and effects of exposure - No data available.

Medical conditions aggravated by exposure - None known.

Indication of the immediate medical attention and special treatment needed

Notes to physician - None.

Fire-fighting measures

Extignuishing media - Extinguish fires with CO2, extinguishing powder, foam, or water.

Special hazards arising from the substance or mixture

Hazardous combustion products - Formation of toxic gases is possible during heating or fire. May include oxides of carbon and nitrogen and products of boron.

Fire/explosion hazards - Fine particles (such as dust and mists) may fuel fires/explosions.

Advice for fire-fighters - During all firefighting activities, wear appropriate protective equipment, including self-contained breathing apparatus.

Accidental release measures

Personal precautions, protective equipment and emergency procedures - Personnel involved in clean-up should wear appropriate personal protective equipment. Minimize exposure.

Environmental precautions - Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.

Methods and material for containment and cleaning up

Measures for cleaning/collecting - Contain the source of the spill if it is safe to do so. Collect spilled material by a method that controls dust generation. Avoid use of a filtered vacuum to clean spills of dry solids. Clean spill area thoroughly.

Additional consideration for large spills - Non-essential personnel should be evacuated from affected area. Report emergency situations immediately. Cleanup operations should only be undertaken by trained personnel.

Handling and storage

Precautions fpr safe handling - Ground and bond all bulk transfer equipment. Avoid open handling. Minimize dust generation. Use local exhaust ventilation or perform work under fume hood/fume cupboard. Avoid inhalation and contact with skin, eye, and clothing. When handling, use appropriate personal protective equipment. Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waster water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls.

Conditions for safe storage, including any incompatibilities.

Storage conditions - Store at room temperature in properly labeled containers. Keep away from heat, sparks and flames.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Exposure controls

Engineering controls - Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels within the OEB range.

Personal protective equipment - Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE). Contact your safety and health professional or safety equipment supplier for assistance in selecting the correct protective clothing/equipment based on an assessment of the workplace conditions, other chemicals used or present in the workplace and specific operational processes.

Hands - Wear 2 layers of impervious disposable gloves (e.g. Nitrile, etc.) to prevent skin contact. (Protective gloves must meet the standards in accordance with EN374, ASTM F1001 or international equivalent.)

Eyes - Wear safety goggles as minimum protection. (Eye protection must meet the standards in accordance with EN166, ANSI Z87.1 or international equivalent.)

Skin - Wear impervious protective clothing to prevent skin contact - consider use of disposable clothing where appropriate. (Protective clothing must meet the standards in accordance with EN13982, ANSI 103 or international equivalent.)

Respiratory protection - Under normal conditions of use, if the applicable Occupational Exposure Band (OEB) is exceeded, waer an appropriate respirator with a protection factor sufficient to control exposures to below the OEB. (Respirators must meet the standards in accordance with EN136, EN143, ASTM F2704-10 or international equivalent.)

Stability and reactivity

Reactivity - No data available.

Chemical stability - Stable under normal conditions of use.

Possibility of hazardous reactions

Oxidizing properties - No data available.

Conditions to avoid - Fine particles (such as dust and mists) may fuel fires/explosions. As a precautionary measure, keep away from heat sources and electrostatic discharge.

Incompatible materials - As a precautionary measure, keep away from strong oxidizers.

Hazardous decomposition products - No data available.

Disposal considerations

Waste treatment methods - Dispose of waste in accordance with all applicable laws and regulations. Member state specific and community specific provisions must be considered. Considering the relevant known environmental and human health hazards of the material, review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure and environmental release. It is recommended that waste minimization be practiced. The best available technology should be utilized to prevent environmental releases. This may include destructive techniques for waste and wastewater.