Registration Dossier

Administrative data

First-aid measures

- First aid responder protection: Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves with appropriate personal protective equipment. Induce artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device. Do not use mouth-to-mouth method if victim ingested or inhaled the substance.
- Following inhalation:
Remove to fresh air. If any trouble breathing, get immediate medical attention. Administer artificial respiration if breathing has ceased. If irritation or symptoms occur or persist, consult a physician.
- Following skin contact:
In case of skin contact, while wearing protective gloves, carefully remove any contaminated clothing, including shoes, and wash skin thoroughly with soap and water. If irritation or symptoms occur or persist, consult a physician.
- Following eye contact:
In case of eye contact, immediately rinse eyes thoroughly with plenty of water. If wearing contact lenses, remove only after initial rinse, and continue rinsing eyes for at least 15 minutes. If irritation occurs or persists, consult a physician.
- Following ingestion:
Rinse mouth and drink a glass of water. Do not induce vomiting unless under the direction of a qualified medical professional or Poison Control Center. If symptoms persist, consult a physician.
- Most important symptoms and effects:

Fire-fighting measures

- Suitable extinguishing media:
Carbon dioxide (CO2), extinguishing powder or water spray.
- Unsuitable extinguishing media:
None known
- Special hazards arising from the substance or mixture:
EXPLOSION HAZARDS: Under normal conditions of use, this material does not present a significant fire or explosion hazard. However, like most organic compounds, this material may present a dust deflagration hazard if sufficient quantities are suspended in air. This hazard may exist where sufficient quantities of finely divided material are (or may become) suspended in air during typical process operations. An assessment of each operation should be conducted and suitable deflagration prevention and protection techniques employed. The sensitivity of this material to ignition by electrostatic discharges has not been determined. In the absence of testing data, all conductive plant items and operations personnel handling this material should be suitably grounded.
THERMAL DECOMPOSITION PRODUCTS: Carbon monoxide (CO). Carbon dioxide (CO2).
- Advice for fire fighter: Wear full protective clothing and self-contained breathing apparatus (SCBA).

Accidental release measures

- Personal precautions:
Avoid generation of dust during clean-up. Wear appropriate personal protective equipment. Keep personnel away from the clean-up area.
- Methods and material for containment and cleaning up: In the case of liquids, use proper absorbent materials. For laboratories and small-scale operations, incidental spills within a hood or enclosure should be cleaned by using a HEPA filtered vacuum or wet cleaning methods as appropriate. For large dry or liquid spills or those spills outside enclosure or hood, appropriate emergency response personnel should be notified. In manufacturing and large-scale operations, HEPA vacuuming prior to wet mopping or cleaning is required.

Handling and storage

Handling: Keep containers adequately sealed during material transfer, transport, or when not in use. Wash face, hands, and any exposed skin after handling. Do not eat, drink, or smoke when using this substance or mixture.
Appropriate handling of this material is dependent onmany factors, including physical form, duration and frequency of process or task, and effectiveness of engineering controls. Site-specific risk assessments should be conducted to determine the feasibility and the appropriateness of all exposure control measures.

Storage: Store at 15-25°C. Store in adequately sealed container.

Transport information

Land transport (ADR/RID)

UN number:
Not subject to the transport regulations
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not subject to the transport regulations
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not subject to the transport regulations
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not subject to the transport regulations
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Hand protection: Gloves that provide an appropriate barrier to the skin are recommended if there is potential for contact with this material. Consult your site safety staff for guidance.
Body protection: In small-scale or laboratory operations, lab coats or equivalent protection is required. Disposable Tyvek or other dust impermeable suit should be considered based on procedure or level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance. In large-scale or manufacturing operations, disposable Tyvek or other dust impermeable suit is recommended and based on level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance.
Eye protection :Safety glasses with side shields. Use of goggles or full face protection may be required based on hazard, potential for contact, or level of exposure. Consult your site safety staff for guidance.
Respiratory protection: Respiratory protective equipment (RPE) may be required for certain laboratory and large-scale manufacturing tasks if potential airborne breathing zone concentrations of substances exceed the relevant exposure limit(s). Workplace risk assessment should be completed before specifying and implementing RPE usage. Potential exposure points and pathways, task duration and frequency, potential employee contact with the substance, and the ability of the substance to be rendered airborne during specific tasks should be evaluated. Initial and ongoing strategies of quantitative exposure measurement should be obtained as required by the workplace risk assessment.All RPE must conform to local and regional specifications for efficacy and performance. Consult your site or corporate health and safety professional for additional guidance.

Stability and reactivity

STABILITY/ REACTIVITY: Stable under normal conditions.
CONDITIONS AND MATERIALS TO AVOID: None known.

Disposal considerations

MATERIAL WASTE:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations. Incineration is the preferred method of disposal, when appropriate. Operations that involve the crushing or shredding of waste materials or returned goods must be handled to meet the recommended exposure limit(s).

PACKAGING AND CONTAINERS:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations.