Registration Dossier

Administrative data

First-aid measures

4.1 DESCRIPTION OF FIRST AID MEASURES
Eye Contact:
Rinse immediately with plenty of water for at least 15 minutes. Obtain medical advice if there are persistent
symptoms.
Skin Contact:
Remove contaminated clothing and shoes without delay. Wash immediately with plenty of water. Do not reuse
contaminated clothing without laundering. Get medical attention if pain or irritation persists after washing or if signs
and symptoms of overexposure appear.
Ingestion:
If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything
by mouth to an unconscious person.
Inhalation:
Remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptoms.
4.2 MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED
None known
4.3 INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDS
Not applicable

Fire-fighting measures

5.1 EXTINGUISHING MEDIA
Suitable Extinguishing Media:
Use water spray, alcohol foam, carbon dioxide or dry chemical to extinguish fires. Water stream may be ineffective.
5.2 SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE
Keep containers cool by spraying with water if exposed to fire.
5.3 ADVICE FOR FIREFIGHTERS
Protective Equipment:
Firefighters, and others exposed, wear self-contained breathing apparatus.

Accidental release measures

6.1 PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES
Where exposure level is not known, wear approved, positive pressure, self-contained respirator. Where exposure
level is known, wear approved respirator suitable for level of exposure. In addition to the protective clothing/equipment
in Section 8 (Exposure Controls/Personal Protection), wear impermeable boots.
6.2 ENVIRONMENTAL PRECAUTIONS
None known
6.3 METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP
Cover spills with some inert absorbent material; sweep up and place in a waste disposal container. Do not flush away
with water. Do not allow spills to enter either drains or waterways. Remove sources of ignition.
6.4 REFERENCES TO OTHER SECTIONS
See Sections 8 and 13 for additional information.

Handling and storage

7.1 PRECAUTIONS FOR SAFE HANDLING
Precautions: Keep away from heat, sparks and open flame. - No smoking. Keep container tightly closed.
Ground/Bond container and receiving equipment. Use explosion-proof electrical, ventilating, lighting and other
equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Wear protective
gloves and eye/face protection. Wash hands thoroughly after handling. Use only outdoors or in a well-ventilated area.
Avoid breathing vapors or spray mist.
Special Handling Statements: Provide good ventilation of working area (local exhaust ventilation if necessary).
During processing and handling of the product, comply with the indicative occupational exposure limit values.
Containers must be bonded and grounded when pouring or transferring material. Within the EEA (EU or Norway) this
substance must be handled under strictly controlled conditions.

7.2 CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES
Store in a cool, dry, well ventilated place and keep container tightly closed. Areas containing this material should have
fire safe practices and electrical equipment in accordance with applicable regulations and/or guidelines. Standards
are primarily based on the material`s flashpoint, but may also take into account properties such as miscibility with
water or toxicity. All local and national regulations should be followed. Keep away from sources of ignition - refrain
from smoking. Avoid flammable gas mixtures. Take precautionary measures against electrostatic loading - earthing
necessary during loading operations. Vapours may form explosive mixtures with air.
Storage Temperature: Store at 5 - 25 °C
Reason: Quality.
Storage Class (TRGS 510): 3

7.3 SPECIFIC END USE(S)
Refer to Section 1 or Exposure Scenario if applicable.

Transport information

Land transport (ADR/RID)

UN number:
UN1866
Proper shipping name and description:
RESIN SOLUTION, flammable
Language:
English
Class:
3
Packaging group:
III
Labels:
Flammable liquid
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
UN1866
Proper shipping name and description:
RESIN SOLUTION, flammable
Language:
English
Class:
3
Packaging group:
III
Labels:
Flammable liquid
Remarks
Not intended for shipment by inland waterways in tank vessels.

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Engineering Measures:
Engineering controls are not usually necessary if good hygiene practices are followed.
Where this material is not used in a closed system, good enclosure and local exhaust ventilation should be provided to control exposure.
Within the EEA (EU or Norway) this substance must be handled under strictly controlled conditions.

Respiratory Protection:
For operations where inhalation exposure can occur use an approved respirator. Recommendations are listed below.
Other protective respiratory equipment may be used based on user's own risk assessment.
Recommended:
Full Face Mask with organic vapor cartridge, Type A filter (BP >65°C)

Eye protection:
Wear eye/face protection such as chemical splash proof goggles or face shield.
Skin Protection:
Avoid skin contact.
Wear impermeable gloves and suitable protective clothing.
Since this product is absorbed through the skin, care must be taken to prevent skin contact and contamination of clothing.

Hand protection:
Wear protective gloves. Recommendations are listed below. Other protective materials may be used based on user's own risk assessment. Barrier creams may help to protect the exposed areas of the skin, they should however not be applied once exposure has occurred. Replace gloves immediately when torn or any change in appearance (dimension, color, flexibility etc.) is noticed.
Gloves for repeated or prolonged exposure - non exhaustive list:
Polyethylene Nylon (PE), thickness: > 0.062 mm, break through time: > 480 min
Gloves for short term exposure/splash protection - non exhaustive list:
Butyl rubber (VB), thickness: 0.30 mm, break through time: up to 75 min
The chemical resistance depends on the type of product and amount of product on the glove. Therefore gloves need to be changed when in contact with chemicals.
Not suitable gloves - non exhaustive list:
Natural rubber (NRL), thickness: 0.12 mm
Due to many conditions (e.g. temperature, abrasion) the practical usage of a chemical protective glove in practice may be much shorter than the permeation time determined through testing. Use PE gloves as under gloves for difficult situations like for instance: high exposure, unknown composition or unknown properties of the chemicals.

Additional Advice:
Before eating, drinking, or smoking, wash face and hands thoroughly with soap and water. It is recommended that a shower be taken after completion of workshift especially if significant contact has occurred. Work clothing should then be laundered prior to reuse. Street clothing should be stored separately from work clothing and protective equipment.
Work clothing and shoes should not be taken home.

Stability and reactivity

10.1 REACTIVITY No information available
10.2 CHEMICAL STABILITY Stable
10.3 POSSIBILITY OF HAZARDOUS REACTIONS
Polymerization: Will not occur
Conditions To Avoid: None known

10.4 CONDITIONS TO AVOID Avoid moisture contamination. Avoid contact with water.

10.5 INCOMPATIBLE MATERIALS
moisture/water

10.6 HAZARDOUS DECOMPOSITION PRODUCTS
None known

Disposal considerations

13.1 WASTE TREATMENT METHODS
The company encourages the recycle and reuse of products and packaging, where possible and permitted.
Product disposal
When recycle or reuse is not possible, the comany recommends that our products, especially when classified as
hazardous, be disposed of by thermal treatment or incineration at approved facilities. All local and national regulations
should be followed. For disposal within the European Community, waste codes according to Directive 2008/98/EC
should be assigned by the user based on the application for which the product was used.
Packaging disposal
Handle contaminated packages in the same way as the product itself. Disposal of emptied and cleaned packaging
must be made in accordance with applicable local and national regulations.
Disposal-relevant information
Do not release directly or indirectly to surface water, ground water, soil or public sewage system.