Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
Immediately remove contaminated clothing.
If inhaled:
Keep patient calm, remove to fresh air, seek medical attention.
On skin contact:
Immediately wash thoroughly with plenty of water, apply sterile dressings, consult a skin specialist.
On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.
On ingestion:
Immediately rinse mouth and then drink plenty of water, do not induce vomiting, seek medical attention.
Most important symptoms and effects, both acute and delayed
Symptoms: The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11.
Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific antidote.

Fire-fighting measures

Extinguishing media
Suitable extinguishing media:
dry powder, foam
Special hazards arising from the substance or mixture
harmful vapours, sulfur oxides
Evolution of fumes/fog. The substances/groups of substances mentioned can be released in case of fire.
Advice for fire-fighters
Special protective equipment:
Wear a self-contained breathing apparatus.
Further information:
The degree of risk is governed by the burning substance and the fire conditions. Contaminated extinguishing water must be disposed of in accordance with official regulations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Use personal protective clothing. Information regarding personal protective measures see, chapter 8.
Environmental precautions
Contain contaminated water/firefighting water. Do not discharge into drains/surface waters/groundwater.
Methods and material for containment and cleaning up
For large amounts: Pump off product.
For residues: Pick up with suitable absorbent material. Dispose of absorbed material in accordance with regulations.
Reference to other sections
Information regarding exposure controls/personal protection and disposal considerations can be found in section 8 and 13.

Handling and storage

Precautions for safe handling
Ensure thorough ventilation of stores and work areas.
Protection against fire and explosion:
Sources of ignition should be kept well clear. Take precautionary measures against static discharges. If delivered in plastic packing, highest permissable emptying temperature is 5 Kelvin below the flash point.
Conditions for safe storage, including any incompatibilities
Further information on storage conditions: Keep container tightly closed and in a cool place.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

Shippingopen allclose all
Labels:

FLAMMABLE LIQUID, CORROSIVE, N.O.S. (contains PROPAN-2-OL, SULFONIUM COMPOUND)
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all

Air transport ICAO/IATA

Remarks
The Guidance on safe use is given for the solution of Sulfonium compounds, C11-14-alkylbis(hydroxyethyl), 2-hydroxyethyl sulfates (salts) in isopropanol. This was done because the registered substance is produced and sold only as a mixture. Therefore also no transport classification for the substance is given.
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Respiratory protection:
Respiratory protection in case of vapour/aerosol release. Particle filter with medium efficiency for solid and liquid particles (e.g. EN 143 or 149, Type P2 or FFP2)
Hand protection:
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374):
Chemical resistant protective gloves (EN 374)
butyl rubber (butyl) - 0.7 mm coating thickness
nitrile rubber (NBR) - 0.4 mm coating thickness
Supplementary note: The specifications are based on tests, literature data and information of glove manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g. temperature) it must be considered, that the practical usage of a chemical-protective glove in practice may be much shorter than the permeation time determined through testing.
Manufacturer's directions for use should be observed because of great diversity of types.
When there is a risk of frostbite from escaping gas, use thermally insulated gloves (EN 511).
Eye protection:
Tightly fitting safety goggles (cage goggles) (e.g. EN 166) and face shield.
Body protection:
Body protection must be chosen based on level of activity and exposure., acid- resp. lye-proof apron, e.g. of rubber (f.e. according to EN 14605), protection boots, f.e. of rubber (e.g. according to EN 20346), acid-proof chemical protection suit (f.e. according to EN 14605)
General safety and hygiene measures
Handle in accordance with good industrial hygiene and safety practice.

Stability and reactivity

Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.
Chemical stability
The product is stable if stored and handled as prescribed/indicated.
Possibility of hazardous reactions
No hazardous reactions when stored and handled according to instructions.
Conditions to avoid
Temperature: > 40 °C
Avoid all sources of ignition: heat, sparks, open flame. Avoid humidity.
Incompatible materials
Substances to avoid:
strong acids, strong bases, strong oxidizing agents
Hazardous decomposition products
Hazardous decomposition products:
No hazardous decomposition products if stored and handled as prescribed/indicated.

Disposal considerations

Waste treatment methods
Must be disposed of or incinerated in accordance with local regulations.
Contaminated packaging:
Uncontaminated packaging can be re-used.
Packs that cannot be cleaned should be disposed of in the same manner as the contents.