legislation-obligation

Substance Regulatory Obligations

OBL

Sulphur dioxide

EC number: 231-195-2

CAS number: 7446-09-5

Last updated: 16/03/2021
ECHA Legislation Regulatory Obligations

Regulatory obligations may exist for this substance under the legislations under ECHA’s remit or for which ECHA has delegated tasks (i.e. REACH, CLP, BPR, PIC, CAD / CMD, WFD, and POPs). Please check the substance Infocard.

Active Implantable Medical Devices Directive

Active Implantable Medical Devices Directive - Hazardous Substances

This list contains hazardous substances for purposes of Directive 90/385/EEC on active implantable medical devices, particularly as regards Article 3 and Annex I (Essential Requirements). This non-exhaustive database is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list).

Name CAS EU CLP (1272/2008) EU_BA Directive 2000/54/EC EU REACH: List of SVHC
sulphur dioxide
7446-09-5
Press. Gas; Acute Tox. 3; Skin Corr. 1B
Ambient Air Quality Directive

Annexes II VII XI XII XIII XIV - Assessment Thresholds & Limit Values

This list contains the Limit, Critical, Target and Long-term Values on ambient air for protection of human health and vegetation. It also contains the Alert, Information and Upper and Lower Assessment thresholds for sulphur dioxide, nitrogen dioxide, benzene, carbon monoxide, lead, PM2.5, PM10 and ozone.

Name CAS Critical Level Alert Threshold Upper assessment threshold Lower assessment threshold Average limit Average sampling duration Tolerance margin Exposure conc. Obligation Information Threshold Long-term objective Objective Target value Annex Qualifier Notes  
Sulphur dioxide
7446-09-5
500 ug/m3
350 ug/m3
1 hour
43 %
Protection of Human Health
XI (Section B),XII (Section A)
01 Without prejudice to Annex I, the criteria for 'Required proportion of valid data' shall be used for checking validity when aggregating data and calculating statistical parameters
02 Limit value not to be exceeded more than 24 times a calendar year
07 Already in force since 1 January 2005
29 Alert thresholds: To be measured over three consecutive hours at locations representative of air quality over at least 100 km2 or an entire zone or agglomeration, whichever is the smaller
30 Average Limit is the Limit Value, a level fixed with the aim of avoiding, preventing or reducing harmful effects on human health and/or the environment and not to be exceeded once attained
Details
Sulphur dioxide
7446-09-5
75 ug/m3
50 ug/m3
125 ug/m3
1 day
0 %
Protection of Human Health
XI (Section B),II (Section A1)
01 Without prejudice to Annex I, the criteria for 'Required proportion of valid data' shall be used for checking validity when aggregating data and calculating statistical parameters
03 Limit value not to be exceeded more than 3 times a calendar year. Applies to Upper and lower thresholds.
07 Already in force since 1 January 2005
14 The required proportion of valid data for the Limit Value referes to the percentage of the hourly averages
30 Average Limit is the Limit Value, a level fixed with the aim of avoiding, preventing or reducing harmful effects on human health and/or the environment and not to be exceeded once attained
Details
Sulphur dioxide
7446-09-5
20 ug/m3
12 ug/m3
8 ug/m3
15 month
0 %
Protection of vegetation
XIII,II (Section A1)
23 The averaging period referes to Calendar year and winter (1 October to 31 March)
27 The upper and lower assessment thresholds correspond to 60% and 40% respectively of winter critical level
Details
CAD - Chemical Agents Directive

CAD - Chemical Agents Directive, Article 2(b)(i) - Hazardous Agents

This list contains a non-exhaustive inventory based on the list of substances with harmonised classification and labelling (i.e., Table 3 of Annex VI to the CLP Regulation 1272/2008/EC). While the harmonised list covers many hazardous substances, others not listed may also meet the classification criteria in accordance with the CLP Regulation.

Name CAS
sulphur dioxide
7446-09-5
Construction Products Regulation

Construction Product Regulation - Annex I (3) - Hazardous Substances

This list contains a non-exhaustive inventory of substances taken from: (1) Table 3 of Annex VI to CLP; (2) the Candidate List of SVHCs; (3) Annex XIV of REACH (Authorisation List); (4) Annex XVII of REACH (Restrictions List); (5) F-gases subject to emission limits/reporting per Regulation 517/2014/EU; and (6) volatile organic compounds (VOCs) listed in the Ambient Air Directive 2008/50/EC. The basis of the list is Annex I(3) of the Construction Products Regulation 305/2011/EC, which stipulates that construction works must not have a high impact on human health or the environment as a result of: giving off toxic gas; emissions of dangerous substances, volatile organic compounds (VOC), greenhouse gases or dangerous particles into indoor or outdoor air; release of dangerous substances into drinking water, ground water, marine waters, surface waters or soil.

Name CAS EU CLP (1272/2008) EU REACH: Annex XIV EU REACH: List of SVHC EU REACH: Annex XVII EU FGG (517/2014) EU VOC (2008/50)
sulphur dioxide
7446-09-5
yes

Construction Product Regulation - Article 6(5) - SDS and Declaration

This list contains a non-exhaustive inventory of substances originating from: (1) Table 3 of Annex VI to CLP (i.e., the list of harmonised substances); (2) the Candidate List of Substances of Very High Concern (SVHCs); and REACH Annex XIV (Authorisation List). This list is compiled on the basis of Article 6(5) of Regulation 305/2011/EC on Marketing of Construction Products. This provision requires SDSs and information on hazardous substances (i.e., SVHCs) contained in construction products be provided with the declaration of performance.

Name CAS EU REACH: Annex XIV EU REACH: List of SVHC
sulphur dioxide
7446-09-5
End-of-Life Vehicles Directive

End-of-Life Vehicles Directive - Hazardous Substances

This list contains a non-exhaustive inventory of hazardous substances as defined by Article 2(11) of the End-of-Life Vehicles Directive 2000/53/EC. It is based on the relevant subset of substances with harmonised classification listed in Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.

Name CAS EU CLP (1272/2008)
sulphur dioxide
7446-09-5
Acute Tox. 3
EU Ecolabel Regulation

Ecolabels - Restrictions for Hazardous Substances/Mixtures

This list contains: (1) the hazardous substances with harmonised classifications and labelling (i.e., Table 3 of Annex VI to CLP Regulation); and (2) the Candidate List of substances of very high concern (SVHC). The EU Ecolabel may not be awarded to substances or mixtures classified as such. Note that this list is not exhaustive. While the harmonised list covers many hazardous substances, others not listed may also meet classification criteria in accordance with the CLP Regulation.

Name CAS Restriction(s) Expressed As Table 3 of Annex VI to CLP EU REACH: List of SVHC Physical form Substance Description  
sulphur dioxide
7446-09-5
yes
Details
General Product Safety Directive

General Product Safety Directive - Hazardous Substances

This list contains a non-exhaustive inventory of substances that fall within the European Union's hazardous substance definitions, as provided on: (1) Table 3 of Annex VI to the CLP Regulation 1272/2008/EC; (2) Annex III of Directive 2000/54/EC (Biological Agents); Candidate List of SVHCs; and REACH Annexes XIV and XVII (Authorisation and Restriction lists). They can be considered hazardous for purposes of the General Product Safety Directive 2001/95/EC.

Name CAS EU CLP (1272/2008) EU REACH: Annex XIV EU REACH: List of SVHC EU REACH: Annex XVII EU_BA Directive 2000/54/EC
sulphur dioxide
7446-09-5
yes
In Vitro Diagnostic Medical Devices Directive

In Vitro Diagnostic Medical Devices Directive - Hazardous Substances

This list contains a non-exhaustive inventory of hazardous substances for purposes of essential requirements (Article 3 and Annex I) for general safety, design, manufacture and hazard communication of in vitro diagnostic medical devices. It is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list).

Name CAS EU CLP (1272/2008) EU_BA Directive 2000/54/EC EU REACH: List of SVHC
sulphur dioxide
7446-09-5
Press. Gas; Acute Tox. 3; Skin Corr. 1B
Industrial Emissions Directive

IPPC - Industrial Emissions Directive, Annex II - Polluting Substances

This list contains the polluting substances for which emission limit values are assigned under Directive 2010/75/EU on Industrial Emissions (Integrated Pollution Prevention and Control - IPPC). Member States must permit all qualifying facilities in order to ensure that they minimize impact on the environment. The permit issued must provide emission limit values for pollutants on this list.

Name CAS Air Water Annex X of Dir 2000/60/EC
Sulphur dioxide
7446-09-5
yes

IPPC, Annexes V, VI, VIII - Provisions relating to industrial plants

This list contains emission limit values for polluting substances in waste gases and waste water, assigned according to facility type (i.e., combustion plants (Annex V), waste incineration/co-incineration plants (Annex VI), and installations producing titanium dioxide (Annex VIII)), under Directive 2010/75/EU on Industrial Emissions (Integrated Pollution Prevention and Control - IPPC). For this list, if a substance presents 2 values in the ''Average sampling duration'' field, these indicate minimum and maximum average sampling period.

Name CAS Expressed As Annex Group Average duration qualifier Average limit Maximum limit Average sampling duration Emission medium fuel Fuel class Part Point Thermal input Process/equipment Qualifier Notes  
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
400 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
250 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Biomass
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Biomass
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Biomass
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
300 mg/nm3
Waste gases
Peat
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
300 mg/nm3
Waste gases
Peat
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Peat
Solid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
09 Combustion plants, using solid fuels which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, and which do not operate more than 1500 operating hours per year as a rolling average over a period of 5 years, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
350 mg/nm3
Waste gases
Liquid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
250 mg/nm3
Waste gases
Liquid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Liquid
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
10 Combustion plants using liquid fuels with a granted permit before 27 Nov 2002 or a submitted complete application for permit before that date, provided that the plant was put into operation before 27 Nov 2003, and with no more than 1500 operating h/year as a rolling average over a period of 5 years, shall be subject to an emission limit for SO2 of 850 mg/Nm3 in case of plants with a total rated thermal input (TRTI) below 300 MW and of 400 mg/Nm3 in case of plants with a TRTI greater than 300 MW
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
35 mg/nm3
Waste gases
In general
Gas
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
5 mg/nm3
Waste gases
Liquified gas
Gas
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
400 mg/nm3
Waste gases
Low calorific gases from coke oven
Gas
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Low calorific gases from blast furnace
Gas
Part 1 (V) Emission limit values for combustion plants referred to in Article 30(2)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
11 Combustion plants, firing low calorific gases from gasification of refinery residues, which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003, shall be subject to an emission limit value for SO2 of 800 mg/Nm3
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
400 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
150 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Coal and lignite and other solid fuels
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
In case of circulating or pressurised fluidised bed combustion
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Biomass
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Biomass
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
150 mg/nm3
Waste gases
Biomass
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
300 mg/nm3
Waste gases
Peat
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
300 mg/nm3
Waste gases
Peat
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
250 mg/nm3
Waste gases
Peat
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
In case of fluidised bed combustion
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
150 mg/nm3
Waste gases
Peat
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Peat
Solid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
In case of fluidised bed combustion
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
350 mg/nm3
Waste gases
Liquid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
50-100
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Liquid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
100-300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
150 mg/nm3
Waste gases
Liquid
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
2
> 300
Combustion plants using solid or liquid fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
35 mg/nm3
Waste gases
In general
Gas
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
5 mg/nm3
Waste gases
Liquified gas
Gas
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
400 mg/nm3
Waste gases
Low calorific gases from coke oven
Gas
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
200 mg/nm3
Waste gases
Low calorific gases from blast furnace
Gas
Part 2 (V) Emission limit values for combustion plants referred to in Article 30(3)
3
Combustion plants using gaseous fuels with the exception of gas turbines and gas engines
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
1000 mg/nm3
Waste gases
Distillation and conversion residues from the refining of crude-oil for own consumption, alone or with other fuels
Part 7 (V) Average emission limit values for multi-fuel firing combustion plants within a refinery
Multi-fuel firing combustion plants within a refinery, with the exception of gas turbines and gas engines
For combustion plants which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
20 See Article 40 for details on multi-fuel firing combustion plants
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
V Annex V (Directive 2010/75/EU) Technical provisions relating to combustion plants
600 mg/nm3
Waste gases
Distillation and conversion residues from the refining of crude-oil for own consumption, alone or with other fuels
Part 7 (V) Average emission limit values for multi-fuel firing combustion plants within a refinery
Multi-fuel firing combustion plants within a refinery, with the exception of gas turbines and gas engines
For combustion plants other than combustion plants which were granted a permit before 27 November 2002 or the operators of which had submitted a complete application for a permit before that date, provided that the plant was put into operation no later than 27 November 2003
00 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correction for the water vapour content of the waste gases and at a standardised O2 content of 6 % for solid fuels, 3 % for combustion plants, other than gas turbines and gas engines using liquid and gaseous fuels and 15 % for gas turbines and gas engines
20 See Article 40 for details on multi-fuel firing combustion plants
37 For technical provisions regarding 'Emission monitoring' see Part 3 (Annex V). For 'Assessment of compliance with emission limit values' see Part 4 (Annex V) Directive 2010/75/EU
38 For technical provisions regarding 'Minimum rate of desulphurisation' see Part 5 (Annex V). For 'Compliance with rate of desulphurisation' see Part 6 (Annex V) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
50 mg/nm3
1 day
Waste gases
Part 3 (VI) Air emission limit values for waste incineration plants
1.1
Waste incineration plants
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6
39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
100 % of the measured values
200 mg/nm3
0.5 hour
Waste gases
Part 3 (VI) Air emission limit values for waste incineration plants
1.2
Waste incineration plants
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6
39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
97 % of the measured values
50 mg/nm3
0.5 hour
Waste gases
Part 3 (VI) Air emission limit values for waste incineration plants
1.2
Waste incineration plants
21 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases.They are standardised at 11 % oxygen in waste gas except in case of incineration of mineral waste oil as defined in point 3 of Article 3 of Directive 2008/98/EC, when they are standardised at 3 % oxygen, and in the cases referred to in Point 2.7 of Part 6
39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
50 mg/nm3
1 day
Waste gases
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
2.3
Cement kilns co-incinerating waste
28 All values are standardised at 10 % oxygen
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
39 For technical provisions regarding 'Monitoring of emissions' see Part 6 (Annex VI). For 'Formula to calculate the emission concentration at the standard percentage oxygen concentration' see Part 7 (Annex VI). For 'Assessment of compliance with emission limit values' see Part 8 (Annex VI) Directive 2010/75/EU
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
400 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass and peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
300 mg/nm3
1 day
Waste gases
Peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
350 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
250 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
33 Emission limit value: linear decrease from 100 to 300 MW of thermal input
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.1
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(2), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
400 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass and peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
300 mg/nm3
1 day
Waste gases
Peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass and peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
300 mg/nm3
1 day
Waste gases
Peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
250 mg/nm3
1 day
Waste gases
Peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; In the case of fluidised bed combustion
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
150 mg/nm3
1 day
Waste gases
Solid fuels with exception of biomass and peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; For circulating or pressurised fluidised bed combustion
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Peat
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines; For all fluidised bed combustion
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
150 mg/nm3
1 day
Waste gases
Biomass
Solid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
31 O2 content 6%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
350 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
50-100
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
200 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
100-300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
33 Emission limit value: linear decrease from 100 to 300 MW of thermal input
Details
Sulphur dioxide
SO2
7446-09-5
VI Annex VI (Directive 2010/75/EU) Technical provisions relating to waste incineration plants and waste co-incineration plants
150 mg/nm3
1 day
Waste gases
Liquid
Part 4 (VI) Determination of air emission limit values for the co-incineration of waste
3.2.2
> 300
Combustion plants co-incinerating waste
For combustion plants referred to in Article 30(3), with the exception of gas turbines and gas engines
30 All emission limit values shall be calculated at a temperature of 273,15 K, a pressure of 101,3 kPa and after correcting for the water vapour content of the waste gases
32 O2 content 3%
Details
Sulphur dioxide
SO2
7446-09-5
As SO2 equivalent
VIII Annex VIII (Directive 2010/75/EU) Technical provisions relating to installations producing titanium dioxide
Gaseous sulphur dioxide and trioxide
6 kg/ton
1 year
Waste gases
Part 2 (VIII) Emission limit values into air
Installations producing titanium dioxide
From digestion and calcination, including acid droplets
40 Emission limit values are given in kg per tonne of titanium dioxide produced, as an annual average
Details
Inland Transport of Dangerous Goods Directive

Inland Transport of Dangerous Goods Directive, Annex I - ADR

This list contains the ADR Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive applies the European Agreements on the international transport of dangerous goods by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID).

Name CAS Class Labels Packing Group Packaging UN No. ADR tank Classification code Hazard identification no. Limited and excepted quantities Vehicle for tank carriage Portable tank and bulk containers Special provisions Special provisions for carriage Transport category (Tunnel restriction code) Notes  
Mixed packing provisions Special packing provisions Packing instructions Tank code Special provisions Excepted quantities Limited quantities Unit Instructions Special provisions bulk Loading, unloading & handling Operation Packages Tunnel restriction code Transport category
SULPHUR DIOXIDE
7446-09-5
2
2.3+8
MP9
P200
1079
PxDH(M)
TA4
TT9
TT10
2TC
268
E0
AT
(M)
T50
TP19
CV9
CV10
CV36
S14
(C/D)
1
1 Not permitted to be carried in limited quantities
Details

Inland Transport of Dangerous Goods Directive, Annex II - RID

This list contains the RID Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive applies the European Agreements on the international transport of dangerous goods by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID).

Name CAS Class Labels Packing Group UN No. Classification code Express parcels Hazard identification number RID Tanks Limited and excepted quantities Packaging Portable tanks and bulk containers Transport category Special provisions for carriage Special provisions Notes  
Tank code Special provisions Excepted quantities Units Limited quantities Special packaging provisions Packaging instructions Mixed packing provisions Special provisions Instructions Loading, unloading & handling bulk Packages
SULPHUR DIOXIDE
7446-09-5
2
2.3+8(+13)
1079
2TC
268
PxDH(M)
TU38
TE22
TE25
TA4
TT9
TT10
TM6
E0
P200
MP9
TP19
T50
(M)
1
CW9
CW10
CW36
1 Not permitted to be carried in limited quantities
Details

Inland Transport of Dangerous Goods Directive, Annex III - ADN

This list contains the ADN Dangerous Goods List, as implemented by the European Union's Directive 2008/68/EC. This Directive establishes rules for the safe transport of dangerous goods between EU countries by road (ADR) and inland waterways (ADN), and the regulations concerning the international carriage of dangerous goods by rail (RID).

Name CAS Class Labels Packing Group UN No. or ID no. Carriage permitted Classification code Equipment required Limited and excepted quantities Number of blue cones/lights Provisions concerning loading, unloading and carriage Ventilation Remarks Special provisions Notes  
Excepted quantities Limited quantities Units Column (11c) Column (11b) Column (11a)
SULPHUR DIOXIDE
7446-09-5
2
2.3+8
1079
2TC
PP
EP
TOX
A
E0
2
VE02
1 Not permitted to be carried in limited quantities
Details
Marine Environmental Policy Framework Directive

Marine Environmental Policy Framework Directive - Hazardous Substances

This list contains a non-exhaustive inventory of hazardous substances for purposes of the Marine Strategy Framework Directive, especially as it concerns Art. 3(8), and Annexes I and III. The listed substances meet the European Union's definitions as hazardous, as provided on: (1) Table 3 of Annex VI to the CLP Regulation (1272/2008/EC); (2) Annex III of Directive 2000/54/EC (Biological Agents); Candidate List of SVHCs; and REACH Annex XIV (Authorisation List).

Name CAS EU CLP (1272/2008) EU REACH: List of SVHC EU_BA Directive 2000/54/EC EU REACH: Annex XIV
sulphur dioxide
7446-09-5
yes
Medical Devices Directive

Medical Devices Directive - Hazardous Substances

This list contains hazardous substances in accordance with the Medical Devices Directive's (MDD) design and construction requirements pursuant to Annex I, Part II (7) & (8) (i.e., chemical, physical and biological properties; and infection and microbial contamination). Specifically, the non-exhaustive database is derived from: Table 3 of Annex VI to CLP, REACH Candidate List of SVHCs, and Directive 2000/54/EC's Annex III (Biological Agents list).

Name CAS EU CLP (1272/2008) EU_BA Directive 2000/54/EC EU REACH: List of SVHC
sulphur dioxide
7446-09-5
Press. Gas; Acute Tox. 3; Skin Corr. 1B
OELs - Occupational Exposure Limits - 4th list

Occupational Exposure Limits - 4th list - Indicative OELVs

This list contains the indicative occupational exposure limit values (IOELVs) from Commission Directive 2017/164/EU. Member States are required to bring into force the laws, regulations and administrative provisions necessary to comply with this Directive, which establishes values for reference period of eight-hour time weighted average and for a short-term period of 15 minutes. The Directive adds limit values for 27 new chemical agents, and amends 6 existing ones established by earlier directives.

Name EC Number CAS Long-term Exposure Limit (LTEL) Values Short-term Exposure Limit (STEL) Values Expressed As Physical form Skin Designation Miscellaneous Notes  
mg/m3 ppm mg/m3 ppm
Sulphur dioxide
231-195-2
7446-09-5
1.3 mg/m3
0.5 ppm
2.7 mg/m3
1 ppm
2 Commission Directive (EU) 2017/164 of 31 January 2017 establishing a fourth list of indicative occupational exposure limit values pursuant to Council Directive 98/24/EC, and amending Commission Directives 91/322/EEC, 2000/39/EC and 2009/161/EU.
Details
Pressure Equipment Directive

Pressure Equipment Directive - Group 1 Fluids Hazardous Substances

This list contains a non-exhaustive inventory of hazardous substances based on Article 13(1)(a) of Directive 2014/68/EU, defining Group 1 fluids for purposes of classifying pressure equipment in accordance with the Directive. The list is derived from a subset of the substances with harmonised classifications, as listed on Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.

Name CAS Substance Description Expressed As Physical form Restriction(s) Index EC Number Classifications
sulphur dioxide
7446-09-5
016-011-00-9
231-195-2
Acute Tox. 3 (Inhalation)
Protection of Young People Directive

Physical, Biological and Chemical Agents & Processes and Work

This list contains biological and chemical agents, in accordance with Art. 7 and points 2 and 3 of the Annex to Directive 94/33/EC, to which young persons (under 18 years of age) may not be exposed at the workplace. The list is a non-exhaustive inventory of such substances based on: 1) agents of risk groups 3 and 4 under Directive 2000/54/EC; 2) Table 3 of Annex VI to the CLP Regulation; 3) and Annex I of Directive 2004/37/EC.

Name CAS EC_YOUNG ECCAR Directive 2004/37/EC EU CLP (1272/2008) EU_BA Directive 2000/54/EC Notes  
sulphur dioxide
7446-09-5
Acute Tox. 3; Skin Corr. 1B
Details
Safety and Health of Workers at Work Directive

Safety and Health of Workers at Work Directive - Hazardous Substances

This list contains a non-exhaustive inventory of substances that fall within the scope of the European Union's definition of hazardous chemical and biological substances, as provided on: (1) Table 3 of Annex VI to the CLP Regulation 1272/2008/EC; and (2) Annex III of Directive 2000/54/EC (Biological Agents). The EU's Occupational Safety and Health (OSH) Framework Directive 89/391/EEC applies to risks arising from chemical, physical and biological agents at the workplace.

Name CAS EU CLP (1272/2008) EU_BA Directive 2000/54/EC
sulphur dioxide
7446-09-5
Press. Gas; Acute Tox. 3; Skin Corr. 1B
Safety and/or Health Signs at Work Directive

Workplace Signs - minimum requirements & signs on containers and pipes

This list contains hazardous substances based on Table 3 of Annex VI to the CLP Regulation 1272/2008/EC. According to the annexes to Directive 92/58/EEC, storage areas and containers containing chemical substances or mixtures that are classified as hazardous according to the CLP Regulation must be duly marked and/or labeled. Directive 92/58/EEC requires employers to ensure proper signage is posted in areas where hazards cannot be avoided or reduced.

Name EC Number CAS Index Sustance Description Danger Symbols Restriction Physical form  
sulphur dioxide
231-195-2
7446-09-5
016-011-00-9
Gas cylinder
Skull and crossbones
Corrosion
Details
WFD - Waste Framework Directive

Waste Framework Directive, Annex III - Waste - Hazardous Properties

This list contains substances that have been assigned hazard property (HP) waste codes 1-15, as defined in terms of the hazard class and category, hazard (H) statement, and/or concentration limits provided in Annex III of the Waste Framework Directive 2008/98/EC. The classifications of the substances listed in the list are based on their harmonised classifications per Table 3 of Annex VI to the CLP Regulation 1272/2008/EC.

Name EC Number CAS EU CLP (1272/2008) HP Code Index
sulphur dioxide
231-195-2
7446-09-5
Acute Tox. 3
Skin Corr. 1B
HP6 Acute Toxicity: waste which can cause acute toxic effects following oral or dermal administration, or inhalation exposure.
HP8 Corrosive: waste which on application can cause skin corrosion.
016-011-00-9

Categories Display