Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 822-547-1
CAS number: 906673-54-9
Eye Contact: Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.
Skin Contact: Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not induce vomiting unless directed by medical personnel. Seek medical attention immediately.
Inhalation: Remove to fresh air and keep patient at rest. Seek medical attention immediately
Extinguishing Media: Extinguish fires with CO2, extinguishing powder, foam, or water.
Special Hazards Arising from the Substance or Mixture
Hazardous Combustion Products: Formation of toxic gases is possible during heating or fire. May include oxides of carbon and nitrogen and products of bromine.
Fire / Explosion Hazards: Fine particles (such as dust and mists) may fuel fires/explosions.
Advice for Fire-Fighters
During all firefighting activities, wear appropriate protective equipment, including self-contained breathing apparatus
Personal Precautions, Protective Equipment and Emergency Procedures: Personnel involved in clean-up should wear appropriate personal protective equipment. Minimize exposure.
Environmental Precautions: Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.
Measures for Cleaning / Collecting:
Contain the source of the spill if it is safe to do so. Collect spilled material by a method that controls dust generation. Avoid use of a filtered vacuum to clean spills of dry solids. Clean spill area thoroughly.
Additional Consideration for Large Spills:
Non-essential personnel should be evacuated from affected area. Report emergency situations immediately. Cleanup operations should only be undertaken by trained personnel
Restrict access to work area. Avoid open handling. Ground and bond all bulk transfer equipment. Minimize dust generation. Use process containment, local exhaust ventilation or perform work under fume hood/fume cupboard. Avoid inhalation and contact with skin, eyes, and clothing. When handling, use appropriate personal protective equipment. Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls.
Storage Conditions: Store at room temperature in properly labeled containers. Keep away from heat, sparks and flames
The purpose of the Occupational Exposure Band (OEB) classification system is to separate substances into different Hazard categories when the available data are sufficient to do so, but inadequate to establish an Occupational Exposure Limit (OEL). The OEB given is based upon an analysis of all currently available data; as such, this value may be subject to revision when new information becomes available.
Engineering Controls: Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels
within the OEB range.
Personal Protective Equipment:
Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE). Contact your safety and health professional or safety equipment supplier for assistance in selecting the correct protective clothing/equipment based on an assessment of the workplace conditions, other chemicals used or present in the workplace and specific operational processes.
Hands: Wear impervious gloves (e.g. Nitrile, etc.) if skin contact is possible. (Protective gloves must meet the standards in accordance with EN374, ASTM F1001 or international equivalent.
Eyes: Wear safety glasses as minimum protection. (Safety glasses must meet the standards in accordance with EN166, ANSI Z87.1 or international equivalent.
Skin: Use protective clothing (uniforms, lab coats, disposable coveralls, etc.) in both production and laboratory areas. (Protective clothing must meet the standards in accordance with EN13982, ANSI 103 or international equivalent.)
Respiratory protection: Under normal conditions of use, if the applicable Occupational Exposure Band (OEB) is exceeded, wear an appropriate respirator with a protection factor sufficient to control exposures
to below the OEB (e.g. particulate respirator with a full mask, P3 filter). (Respirators must meet the standards in accordance with EN136, EN143, ASTM F2704-10 or international equivalent.)
Reactivity: No data available
Chemical Stability: Stable under normal conditions of use.
Possibility of Hazardous Reactions
Oxidizing Properties: No data available
Conditions to Avoid: Fine particles (such as dust and mists) may fuel fires/explosions. As a precautionary measure, keep away from heat sources and electrostatic discharge. Incompatible Materials: As a precautionary measure, keep away from strong oxidizers
Hazardous Decomposition Products: No data available
Dispose of waste in accordance with all applicable laws and regulations. Member State specific and Community specific provisions must be considered. Considering the relevant known environmental and human health hazards of the material, review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure and environmental release. It is recommended that waste minimization be practiced. The best available technology should be utilized to prevent environmental releases. This may include destructive techniques for waste and wastewater
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
Sellel veebilehel kasutatakse küpsiseid, et tagada lehe parim kasutus.
Welcome to the ECHA website. This site is not fully supported in Internet Explorer 7 (and earlier versions). Please upgrade your Internet Explorer to a newer version.
Do not show this message again